header print

3 Amazing Methods For Re-purposing Clay Pots

Clay pots seem like the most useless of things if you don’t happen to be growing plants in them, but did you know that there’s a ton of different ways that they can be re-used? Here are three novel ideas for turning your clay pots into something really special:
 

1. Terra Cotta Fountain

Materials: 

•    Upper bowl approximately 21” in diameter 
•    Lower basin approximately 32” in diameter 
•    Planter 
•    Small terra cotta dish 
•    Water pump 
•    Plastic cord
•    Plastic pipe plug x 2 
•    Pipe bushing
•    Plastic pump output tube 
•    Garden hose fitting
•    Large brass washer 
•    Soldering iron 
•    1/2” Copper riser pipe 
•    Female garden hose connector 
•    Shouldered bushing

Method:

1. Place the fountain pump in the basin and affix.

clay-pots
2. Drill the plastic pipe plug to accept the cord and thread it through. You’ll need to cut the electrical plug off the end of the pump power cord to do this.
clay-pots
3. Put on a new plug after you’re done and seal with silicone. Check the cord for any cuts and connections that might be underwater.
clay-pots
4. Glue the pipe bushing into the bottom hole of the Terra Cotta pipe plug. This allows the pipe plug to be unscrewed in order to remove the complete power cord intact ready for winter storage.
clay-pots
5. Position the pump in the center of the Terra Cotta bowl. The rigid plastic pump output tube should face upward and will help the pump stay in place thanks to passing through the parts of the fountain that are placed above it.
clay-pots
6. Invert the planter and place it over the pump in the center of the basin. This supports the upper bowl of the fountain.
clay-pots
7. Solder the garden hose fitting into the large brass washer. Glue them into the upper bowl.
clay-pots
8. Slide the copper riser pipe over the plastic pump tube. Solder the female garden hose connector to the lower end of the pipe complete with its usual rubber gasket inside. This forms a leak-tight seal for the upper bowl.
clay-pots

9. Add a shouldered bushing to the top of the riser pipe in order to support the small terra cotta dish. This is used to catch water bubbling out of the riser and spreads it to drip into the basin below for aeration.

2. Flowerpot Bird Feeder
clay-pots

Materials: 

•    Terracotta or clay flowerpot and two saucers. I used an orchid pot (which has pre-drilled holes), but I also made one out of an azalea pot and drilled seed holes (any flowerpot that you have on hand and want to re-purpose as a feeder will work). The saucer needs to cover the top of the flowerpot (as a lid). 
•    Glass and tile drill bits (1/2" for seed openings, 1/8" for hanging)
•    3/32" vinyl coated wire rope (about 2 feet) 
•    1/8" ferrule and stop set
•    Pliers

clay-pots

Method: 

1. Drill 1/8” holes in the center of each saucer. Use the appropriate drill bit.

2. Add three drainage holes to the base saucer.

3. Use a 1/2” bit to drill three seed holes about one inch from the bottom of the flowerpot.

4. Thread the wire rope through the top saucer, flower pot, and base saucer.

5. Clamp the ferrule using pliers and stop onto the wire at the base and top.

6. Add a few embellishments to the bird feeder to improve its appearance if you wish.

3. DIY Garden Mushrooms
clay-pots

Materials: 

•    2-3 round terra cotta pots in various sizes
•    2-3 round terra cotta drain plates (each 3-5 in. wider than the bottom of the matching pot)
•    Spray paint, in white, and in choice of colors for mushroom tops
•    White acrylic craft paint
•    Waterproof clear paint- on or spray sealer
•    2-in.-wide round sponge or spouncer
•    Small paintbrush
•    Epoxy or waterproof outdoor glue (optional)

Method: 

1. Spray-paint the exterior of the pots white in a well-ventilated area, and spray their undersides in a contrasting color. Apply as many coats of spray as required, and leave to dry for 24-48 hours.

2. To create the dots on the mushroom tops, dip a round sponge or spouncer in white acrylic paint. Coat it liberally and then press it to a painted drain plate. Remove quickly to leave a white dot. Fill in any light areas of paint with a small paintbrush.

3. Repeat step two, making several randomly-placed white dots on each painted drain plate. Leave all the dots to dry completely.

4. After they’re done drying, coat all painted surfaces with a layer of clear, waterproof sealer. Leave to dry for 24 to 48 hours.

5. Center a drain plate, painted side up, on top of each upside-down pot. Use epoxy or waterproof outdoor glue to adhere the drain plate to the base.

6. Find a good spot in your garden to display your fabulous new DIY mushrooms!

 

Content and image source 

Next Post
Sign Up for Free Daily Posts!
Did you mean:
Continue With: Facebook Google
By continuing, you agree to our T&C and Privacy Policy
Sign Up for Free Daily Posts!
Did you mean:
Continue With: Facebook Google
By continuing, you agree to our T&C and Privacy Policy